A Beginner's Guide to Installing a Bathtub
A Beginner's Guide to Installing a Bathtub
Blog Article
We have found this article relating to A Step-by-Step Guide to Installing a Bathtub directly below on the web and thought it made good sense to talk about it with you in this article.
Installing a bathtub isn't specifically rocket science, yet it does need strong plumbing, carpentry, as well as sometimes, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably difficult job. If the old bathtub is easily obtainable, the project can relocate speedily; if you have to open up a wall surface to get rid of the old tub and also position the brand-new bath tub, the job is a lot harder. In either instance, the project is within a house handyman's abilities, although you will require an assistant to move out the old tub and also embeded in the new one. Make sure you have certified yourself for the job and are comfortable attempting it. Rather than hiring a service provider to take over a halfway-completed task, it is much better to consider utilizing one before you start. Opportunities are you might require an expert plumber to make tube links.
This post will certainly assist you set up a brand-new tub in your shower room if you have currently purchased a new bathtub and also don't require to alter the arrangement of your previous water supply pipelines.
Your tools and product checklist should make up the following:
Planning for the Installation
First of all, the sustaining structure supplied with the bath must be fitted (if needed) according to the producer's directions. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is essential to see to it that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to avoid stress on the tub.
Fit the versatile faucet adapters to the bottom of both taps utilizing 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you utilize all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must now prepare to be fitted in its last setting.
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, then the first thing you must do is disconnect the supply of water. After doing so, turn on the faucets to drain any water remaining in the system. The procedure of removing the existing faucets can be fairly troublesome as a result of the restricted gain access to that is frequently the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the faucets. Have a towel ready for the continuing to be water that will come from the pipelines. Once the supply pipelines have been removed, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from turning during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
Prior to moving on to fit the brand-new faucets, compare the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Mounting the Tub
Using the two wood boards under its feet, place the bathtub in the needed position. The wooden boards are valuable in equally spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 small factors.
The next goal is to ensure that the tub is leveled all round. This can be attained by checking the level as well as readjusting the feet on the bathtub until the level reads level.
To set up faucets, fit all-time low of the outermost adaptable tap adapter to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the other faucet.
Switch on the water and check all joints and brand-new pipework for leakages and also tighten them if required. Fill the tub as well as additionally examine the overflow electrical outlet and also the typical electrical outlet for leakages.
Ultimately, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bathtub must wait till the bathtub has been utilized at the very least once as this will certainly settle it into its last position.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the tap and the various other end provides a connection to the current supply pipes.
If you require to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin making sure that the washers are in area in between the tap and the sink. Safeguard the tap in place with the producer provided backnut. Once the faucet is securely in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical tap adapters. The previous kind should be linked to the faucet finishes first, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to fracture a rigid seal, causing the water to permeate the wall between the bathroom and the tiling, leading to issues with moisture and feasible leaks to the ceiling below.
You can select from a range of coloured sealants to blend in your components and installations. They are sold in tubes as well as cartridges, as well as can securing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with twists of soaked paper or soft rope. Remember to constantly fill up the bathtub with water before sealing, to enable the movement experienced when the tub is in use. The sealer can split rather early if you do not think about this activity prior to securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently readily available on the marketplace. It is recommended to fit the tiles making use of waterproof or water resistant adhesive and also grout.
Bathtub Installation
How Important Is A Bathtub To Your Home?
High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.
Install Piping Before Tub
You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.
Position the Tub
Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.
NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.
Assemble Drain Connections
Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.
Place a Pipe For the Shower Head
First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.
Attaching Hot and Cold Water Lines
Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.
Install the Spout
Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.
NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.
Check For Leaks
Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.
estore the Bathroom Wall
Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.
https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/
Hopefully you enjoyed reading our post on Tools You Need to Install a New Bathtub . Thanks for taking the time to read our piece of content. In case you liked our article if you please make sure you remember to share it. Thank you for taking the time to read it.
Clogged drain? Phone! Report this page